Trial design This study is a 3-arm parallel-group, randomized controlled trial with a 1:1 allocation ratio.
Participants, eligibility criteria, and setting
Participants are to be recruited at the Postgraduate Dental Education Center, Department of Orthodontics, in Örebro, Henrikson Orthodontics, in Malmö and Universitat Internacional de Catalunya, Department of Orthodontics, in Barcelona.
The following inclusion criteria is to be applied:
* Patients requiring mandibular lingual fixed canine-to-canine retainer after undergoing orthodontic treatment with fixed appliances
* Sound enamel on the lingual surface
* Calculus-free lingual surface in the lower anterior segment
Interventions
After informed consent is obtained, the patients are going to be randomized into three groups:
Group 1: Penta-One 0.0215 inch multistranded wire
Group 2: Ortho-FlexTech stainless steel chain
Group 3: Memotain wire
Procedures For all groups the time required for taking impressions and bonding of retainers is taken by a digital timer.
Patients allocated to Group 1:
After taking impressions and when the working models are cast in hard stone, all retainers (0.0215-inch multistranded Penta-one wire) are going to be contoured by dental technicians at each center.
All retainers in the study are to be bonded using the following sequence of construction.
* The fixed appliance is debonded, and the teeth are to be thoroughly cleaned and polished using oil-free pumice.
* After adequate moisture control using dental cotton rolls in the anterior segment, parotis dental rolls in the lateral segments, and saliva ejector, the lingual surfaces are to be sandblasted in half of the group (according to the randomization list)
* Lingual surfaces are etched with Ultra-Etch 35% phosphoric acid gel (Ultradent Products Inc, City, Utah), for 30 seconds and thoroughly rinsed and dried.
* A thin layer of primer Ortho Solo® (Ormco, Orange, CA, USA) applies.
* Retainer holds in place with dental floss and the fit is checked.
* Adequate amounts of composite Tetric Evo-Flow (Ivoclar Vivadent, Schaan, Liechtenstein) is applied to the lingual surfaces of the six anterior teeth over the retainer, ensuring maximum coverage of the wire surface. The composite pads are light cured, both incisally and cervically, for 20 seconds per tooth.
Patients allocated to Group 2:
* The fixed appliance is debonded, and the teeth are to be thoroughly cleaned and polished using oil-free pumice.
* After adequate moisture control using dental cotton rolls in the anterior segment, parotis dental rolls in the lateral segments, and saliva ejector, the lingual surfaces are to be sandblasted in half of the group (according to the randomization list)
* Lingual surfaces are etched with Ultra-Etch 35% phosphoric acid gel (Ultradent Products Inc, City, Utah), for 30 seconds and thoroughly rinsed and dried.
* A thin layer of primer Ortho Solo® (Ormco, Orange, CA, USA) applies.
* Small amounts of composite Tetric Evo-Flow (Ivoclar Vivadent, Schaan, Liechtenstein) were applied to the lingual surfaces of the six anterior teeth.
* Ortho-FlexTech chain is cut at chairside in desired length and hold in place with dental floss and the fit is checked.
* Small amounts of composite Tetric Evo-Flow (Ivoclar Vivadent, Schaan, Liechtenstein) is applied to the lingual surfaces of the six anterior teeth over the retainer, ensuring maximum coverage of the wire surface. The composite pads are light cured, both incisally and cervically, for 20 seconds per tooth. Additional composite applies to cover the whole mesial-deistal surface of each tooth making sure not to cover the approximal surfaces. Then light cured for another 20 second per tooth.
Patients allocated to Group 3:
* After digital scanning of the anterior lower six teeth, the Memotain in ordered online.
* The fixed appliance is debonded, and the teeth are to be thoroughly cleaned and polished using oil-free pumice.
* After adequate moisture control using dental cotton rolls in the anterior segment, parotis dental rolls in the lateral segments, and saliva ejector, the lingual surfaces are to be sandblasted in half of the group (according to the randomization list)
* Lingual surfaces are etched with Ultra-Etch 35% phosphoric acid gel (Ultradent Products Inc, City, Utah), for 30 seconds and thoroughly rinsed and dried.
* A thin layer of primer Ortho Solo® (Ormco, Orange, CA, USA) applies.
* Memotain puts into placed using the positioning jig to ensure precise placement.
* Adequate amounts of composite Tetric Evo-Flow (Ivoclar Vivadent, Schaan, Liechtenstein) are applied to the lingual surfaces of the canines initially and after removing the positioning jig on the remaining four anterior teeth, ensuring maximum coverage of the wire surface. The composite pads are light cured, both incisally and cervically, for 20 seconds per tooth.
Follow-ups During the visit to the clinics all groups are to take impressions with digital scanning of the upper and the lower dentition and intraoral photographs from the dentition at baseline (directly after debond) T0, 6 months after debond (T1), one year (T2) two years (T3) and five years (T4) after debond.
The digital study models will be assessed for identifying possible side effects and deviation of individual tooth positions. For this purpose Little's Irregularity Index (LII) (9) for tooth contact displacement will be used. Patients' records will be reviewed to assess the first debond or breakage of the retainers during the observation periods.
To determine the cost-effectiveness, the overall cost of the retainers including manufacturing, time for impressions and bonding will be calculated and compared.
Failure of a retainer can occur as a result of debonding, fracture, debonding and fracture, or retainer loss. Information on the site of failure e.g. single tooth bond failure, enamel/adhesive failure, or adhesive wire failure is to be recorded in the patients' records.
Only first failures are to be counted and failure location (which tooth) is to be noted. In addition, multiple failure sites in one retainer are going to be counted as one failure. Furthermore, failure is considered when there was debonding, fracture, debonding and fracture, or retainer loss.
Outcomes The primary outcome is failure rate/breakage of the retainers during the observation period.
Secondary outcome include, complications (such as BoP, calculus, caries, gingivitis), costs and the effect of micro-etching (sand blasting) on the failure rate.
Sample size estimation The calculated sample size for each group is based on a significance level of 0.05 and 90 per cent power to detect a clinically meaningful difference of 15 per cent failure rate between the groups. The sample size calculation indicated that 97 patients would be required in each group. To compensate for dropouts, we decided to include at least 108 patients in each group (an addition of 10 per cent per group) and a total of 324 patients.
